К сожалению, мы не смогли определить Ваш город (ip=3.138.124.143)
Пожалуйста, укажите его самостоятельно
Поиск по идентификационному номеру VIN
Поиск по номеру детали

Автозапчасти Mercedes

Каталог Mercedes→Категория «Легковой а/м»→Раздел «FG - шасси»→Модельный ряд «TYP 180D BM 120.110-.111, .100-.102»→Группа 07 - INJECTION PUMP, MIXTURE CONTROLLER, SUCTION NOISE DAMPER, SUCTION PIPE AND EXHAUST MANIFOLD

Группа 07 → INJECTION PUMP, MIXTURE CONTROLLER, SUCTION NOISE DAMPER, SUCTION PIPE AND EXHAUST MANIFOLD

Подгруппа 005 → INJECTION PUMP

№ поз. Номер детали Название/дополнительная информация Колич Версия
INJECTION PUMP
----- A 000 074 93 02→€ REPLACED BY
002 074 01 01 TOGETHER WITH 1 STOP ANGLE 636 074 02 40 UP TO ENGINE 5516035 		0
----- A 001 074 54 01→€ INJECTION PUMP

Заменено на: A 002 074 01 01→€ 		0
1 A 002 074 01 01→€ INJECTION PUMP
FROM ENGINE 5516036 		1
----- A 001 074 34 01→€

Заменено на: A 002 074 02 01→€ 		0
----- A 001 074 77 01→€ INJECTION PUMP

Заменено на: A 002 074 02 01→€ 		0
----- A 002 074 02 01→€ INJECTION PUMP

Текстовая сноска
СноскаОписание
[003]SPECIAL REQUEST FOR COUNTRIES MORE THAN 2000 M HIGH
 		1
----- A 636 074 01 40→€ STOP ANGLE
FOR CHOKE AND STOPPER CABLE AT INJECTION PUMP UP TO ENGINE 5516035 		1
2 A 636 074 02 40→€ STOP ANGLE
FOR CHOKE AND STOPPER CABLE AT INJECTION PUMP FROM ENGINE 5516036 		1
3 A 000 074 03 15→€ PRESSURE VALVE
WITH VALVE SUPPORT 		4
4 A 000 074 16 93→€ COIL SPRING
FOR PRESSURE VALVE 		4
----- A 000 997 23 40→€ SEALING RING
FOR PIPE CONNECTIONS

Заменено на: A 001 997 30 40→€ 		0
5 SEALING RING
001 997 3040 FOR PIPE CONNECTIONS 		4
6 A 000 078 00 69→€ PIPE CONNECTION
FOR PRESSURE VALVES 		4
----- A 000 078 01 35→€ CLAMPING JAW WITH THREAD
TO CLAMP PIPE CONNECTIONS

Заменено на: A 000 078 03 35→€ 		0
7 A 000 078 03 35→€ CLAMPING JAW WITH THREAD
TO CLAMP PIPE CONNECTIONS 		2
8 A 000 078 02 35→€ CLAMPING JAW
WITHOUT THREAD TO CLAMP PIPE CONNECTIONS 		2
----- COUNTERSUNK SCREW
AM 6X22 DIN 63-4 S FOR CLAMPINGJAWS 000 078 01 35/00 35 		2
----- CYLINDRICAL SCREW
BM 6X28 DIN 84-4 S FOR CLAMPINGJAWS 000 078 02 35/03 35 		2
----- LOCK WASHER
B 6 DIN 127 FOR CLAMPINGJAWS 000 078 02 35/03 35 		2
----- SEALING RING
A 6X10 DIN 7603 A1 FOR BREATHER SCREW 		2
----- A 000 074 01 71→€ BREATHER SCREW
ON INJECTION PUMP, FRONT SIDE

Заменено на: A 000 074 06 71→€ 		0
11 A 000 074 06 71→€ BREATHER SCREW
ON INJECTION PUMP, FRONT SIDE 		2
----- SEALING RING
A 10X14 DIN 7603 A1 FOR ANNULAR FITTING 		2
----- ANNULAR FITTING
B 4 DIN 7622 FOR OIL OVERFLOW 		1
----- HOLLOW SCREW
A 4 DIN 7623 TO FIX ANNULAR FITTING, FOR OIL OVERFLOW 		1
----- A 000 074 10 60→€ OIL DIPSTICK

Заменено на: A 000 074 13 60→€ 		0
17 A 000 074 13 60→€ OIL DIPSTICK 1
18 A 000 075 00 32→€ BREATHER FILTER
ON GOVERNOR 		1
----- SEALING RING
A 12X16 DIN 7603CU 		1
----- A 000 075 02 07→€ DIAPHRAGM
FOR GOVERNOR

Текстовая сноска
СноскаОписание
[004]FOR INJECTION PUMP 000 074 93 02 UND 001 074 34 01
 		1
----- A 000 075 03 07→€ DIAPHRAGM
FOR GOVERNOR

Текстовая сноска
СноскаОписание
[005]FOR INJECTION PUMP 001 074 54 01 UND 001 074 77 01
 		1
20 A 000 075 04 07→€ DIAPHRAGM
FOR GOVERNOR

Текстовая сноска
СноскаОписание
[006]FOR INJECTION PUMP 002 074 01 01 UND 002 074 02 01
 		1
FUEL PUMP
25 A 000 091 41 01→€ FUEL PUMP
WITHOUT PRE-FILTER 		1
26 A 000 091 00 10→€ VALVE
SUCTION AND PRESSURE VALVE 		2
27 A 000 091 03 19→€ PRESSURE SPRING
FOR SUCTION AND PRESSURE VALVE 		2
28 A 000 997 07 30→€ SCREW PLUG
FOR PRESSURE VALVE 		1
29 A 000 091 11 01→€ HAND PUMP
FOR FUEL PUMP 		1
----- SEALING RING
A 14X20 DIN 7603 A1 FOR HOLLOW SCREW 		2
----- HOLLOW SCREW
A 8 DIN 7623 FOR FUEL LINE AT FUEL PUMP 		1
35 A 000 091 05 80→€ GASKET
BETWEEN FUEL PUMP AND INJECTION PUMP 		1
----- WASHER
6,4 DIN 433 FOR FUEL PUMP AT INJECTION PUMP 		3
----- LOCK WASHER
B 6 DIN 127 FOR FUEL PUMP AT INJECTION PUMP 		3
----- HEX. NUT
M 6 DIN 934-5 S FOR FUEL PUMP AT INJECTION PUMP 		3
39 A 000 074 27 27→€ CONTROL LEVER
ON CONTROL SHAFT TO INJECTION PUMP 		1
----- LOCK WASHER
B 5 DIN 127 FOR CONTROL LEVER ON CONTROL SHAFT 		1
----- HEX.-HD.SCREW
M 5X15 DIN 933-8 G FOR CONTROL LEVER ON CONTROL SHAFT 		1
----- WOODRUFF KEY
2X3,7 DIN 6888 FOR CONTROL LEVER ON CONTROL SHAFT 		1
----- WASHER
5,3 DIN 433 OPTIONAL FOR CHOKE AND STOPPER CABLE AT CONTROL LEVER 		1
----- SPRING WASHER
5 N 55 A OPTIONAL FOR CHOKE AND STOPPER CABLE AT CONTROL LEVER 		1
----- COTTER PIN
1,5X12 DIN 94 FOR CHOKE AND STOPPER CABLE AT CONTROL LEVER 		1
----- WOODRUFF KEY
3X5 DIN 6888 		1
51 A 636 077 03 09→€ FOLLOWER
FOR INJECTION PUMP 		1
----- LOCK WASHER
B 12 DIN 127 FOR FOLLOWER AT INJECTION PUMP 		1
----- HEX. NUT
M 12 DIN 934-5 S FOR FOLLOWER AT INJECTION PUMP 		1
----- SEALING RING
A 12X16 DIN 7603 A1 		1
----- THREADED NIPPLE
6 DIN 7627 FOR CONNECTION OF VACUUM LINE BETWEEN INJECTION PUMP GOVERNOR AND MIXTURE CONTROLLER UP TO ENGINE 8500349 		1
56 A 636 074 04 80→€ GASKET
BETWEEN TIMING GEAR CASE COVER AND INJECTION PUMP 		1
----- WASHER
10,5 DIN 125 FOR INJECTION PUMP AT TIMING GEAR CASE COVER 		4
----- HEX. NUT
M 10 DIN 934-5 S FOR INJECTION PUMP AT TIMING GEAR CASE COVER 		4
----- GROOVED BEARING
16002 DIN 625 UP TO ENGINE 4500145 		2
----- GROOVED BEARING
6202 DIN 625 FROM ENGINE 4500146 		2
----- LOCKING RING
32X1,2 DIN 472 UP TO ENGINE 4500145 		2
----- LOCKING RING
35X1,5 DIN 472 FROM ENGINE 4500146 		2
----- A 636 077 02 05→€ DRIVE SHAFT
FOR INJECTION PUMP UP TO ENGINE 4505074 		1
----- A 636 077 04 05→€ DRIVE SHAFT
FOR INJECTION PUMP FROM ENGINE 4505075-5514611 		1
61 A 636 077 05 05→€ DRIVE SHAFT
FOR INJECTION PUMP FROM ENGINE 5514612 		1
----- A 636 077 00 53→€ SPACER TUBE
BETWEEN GROOVED BEARINGS ON DRIVE SHAFT UP TO ENGINE 4500145 		1
----- A 636 077 02 53→€ SPACER TUBE
BETWEEN GROOVED BEARINGS ON DRIVE SHAFT FROM ENGINE 4500146-4505074 		1
62 A 636 077 01 53→€ SPACER TUBE
BETWEEN GROOVED BEARINGS ON DRIVE SHAFT FROM ENGINE 4505075 		1
63 A 636 077 01 52→€ ADJUSTING RING
FOR DRIVE SHAFT FROM ENGINE 4505075-5514611 		1
----- WOODRUFF KEY
3X5 DIN 6888 FOR DRIVE GEAR, OR INJECTION TIMING GEAR RESP., AT DRIVE SHAFT 		1
----- A 636 077 02 12→€ DRIVE GEAR, 40 TEETH
FOR INJECTION PUMP UP TO ENGINE 5514611 		1
65 A 636 070 00 45→€ INJECTION TIMING GEAR
FROM ENGINE 5514612 		1
66 A 636 075 01 25→€ SEGMENT FLANGE
FROM ENGINE 5514612 		1
67 A 636 075 00 35→€ BALANCING WEIGHT
FROM ENGINE 5514612 		2
68 A 636 075 00 25→€ SEGMENT PLATE
FROM ENGINE 5514612 		1
----- A 636 075 01 74→€ PIN
FOR SPRING SEAT FROM ENGINE 5514612

Заменено на: A 621 075 02 74→€ 		0
69 A 621 075 02 74→€ PIN
FOR SPRING SEAT FROM ENGINE 5514612 		4
----- A 636 993 03 01→€ PRESSURE SPRING
FROM ENGINE 5514612

Заменено на: A 636 993 05 01→€ 		0
70 A 636 993 05 01→€ PRESSURE SPRING
FROM ENGINE 5514612 		2
----- A 636 075 00 74→€ PIN
FOR TIMING LIMIT FROM ENGINE 5514612

Заменено на: A 621 075 01 74→€ 		0
71 A 621 075 01 74→€ PIN
FOR TIMING LIMIT FROM ENGINE 5514612 		2
72 A 636 077 06 12→€ DRIVE GEAR
FROM ENGINE 5514612 		1
----- A 636 070 00 54→€
FROM ENGINE 5514612

Заменено на: A 636 075 03 50→€ 		0
----- A 636 075 00 50→€ BUSHING
FOR DRIVE GEAR FROM ENGINE 5514612

Заменено на: A 636 075 03 50→€ 		0
73 A 636 075 03 50→€ BUSHING
FOR DRIVE GEAR FROM ENGINE 5514612 		1
----- SPRING WASHER
B 8 DIN 137 FROM ENGINE 5514612 		4
----- HEX.-HD.SCREW
M 8X12 DIN 933-8 G FROM ENGINE 5514612 		4
76 A 636 075 00 62→€ THRUST WASHER
FROM ENGINE 5514612 		1
----- WASHER
13 DIN 125 FOR DRIVE GEAR, OR INJECTION TIMING GEAR RESP., AT DRIVE SHAFT 		1
----- LOCK WASHER
B 12 DIN 127 FOR DRIVE GEAR, OR INJECTION TIMING GEAR RESP., AT DRIVE SHAFT 		1
----- HEX. NUT
M 12X1,5 DIN 934-5 S FOR DRIVE GEAR, OR INJECTION TIMING GEAR RESP., AT DRIVE SHAFT 		1
UNIT PARTS FOR SUBSEQUENT INSTALLATION OF INJECTION TIMING GEAR
----- A 636 070 00 99→€ UNIT PARTS
FOR SUBSEQUENT INSTALLATION OF INJECTION TIMING GEAR UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDIT 		1
----- A 636 070 00 45→€ INJECTION TIMING GEAR
UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 1 SPACER T 		1
----- A 636 075 00 62→€ THRUST WASHER
UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 1 SPACER T 		1
----- A 636 077 05 05→€ DRIVE SHAFT
UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 1 SPACER T 		1
----- A 636 015 05 30→€ COVER
UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 1 SPACER T 		1
----- WASHER
13 DIN 125 UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 		1
----- A 636 092 04 20→€ SHIM
UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 1 SPACER T 		1
----- HEX.-HD.SCREW
M 12X55 DIN 931-8 G UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 		2
----- A 636 015 02 71→€ FIXING SCREW
WITH TIMING NEEDLE UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 0 		1
----- WITH THE
FOLLOWING INSTALLED PARTS TO BE REMOVED: DRIVE SHAFT 636 077 04 05 DRIVE GEAR 636 077 02 12 COVER 636 015 01 30 HEX.-HD. 		0
----- A 636 077 01 16→€ COUPLING SLEEVE
FOR INJECTION PUMP DRIVE UP TO ENGINE 4500145 		1
80 A 636 077 02 16→€ COUPLING SLEEVE
FOR INJECTION PUMP DRIVE FROM ENGINE 4500146 		1
81 A 636 994 01 35→€ SNAP RING
IN COUPLING SLEEVE 		1
NOZZLE HOLDER
82 A 000 017 28 21→€ NOZZLE HOLDER
WITH INJECTION NOZZLE 		4
----- A 000 017 31 21→€ NOZZLE HOLDER BODY 4
----- A 000 017 04 54→€ THROUGH FITTING
FOR CONNECTION OF LEAK OIL LINE

Заменено на: A 000 017 06 54→€ 		0
83 A 000 017 06 54→€ THROUGH FITTING
FOR CONNECTION OF LEAK OIL LINE 		4
84 A 000 017 02 55→€ HEX. NUT
TO FIX THROUGH FITTING ON NOZZLE HOLDER BODY 		4
----- A 000 017 29 52→€ SHIM, 1.0 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 36 52→€ 		0
85 A 000 017 36 52→€ SHIM, 1.0 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 30 52→€ SHIM, 1.05 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 37 52→€ 		0
----- A 000 017 37 52→€ SHIM, 1.05 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 12 52→€ SHIM, 1.10 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 38 52→€ 		0
----- A 000 017 38 52→€ SHIM, 1.10 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 13 52→€ SHIM, 1.15 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 39 52→€ 		0
----- A 000 017 39 52→€ SHIM, 1.15 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 14 52→€ SHIM, 1.20 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 40 52→€ 		0
----- A 000 017 40 52→€ SHIM, 1.20 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 15 52→€ SHIM, 1.25 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 41 52→€ 		0
----- A 000 017 41 52→€ SHIM, 1.25 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 16 52→€ SHIM, 1.30 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 42 52→€ 		0
----- A 000 017 42 52→€ SHIM, 1.30 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 17 52→€ SHIM, 1.35 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 43 52→€ 		0
----- A 000 017 43 52→€ SHIM, 1.35 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 18 52→€ SHIM, 1.40 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 44 52→€ 		0
----- A 000 017 44 52→€ SHIM, 1.40 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 19 52→€ SHIM, 1.45 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 45 52→€ 		0
----- A 000 017 45 52→€ SHIM, 1.45 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 20 52→€ SHIM, 1.50 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 46 52→€ 		0
----- A 000 017 46 52→€ SHIM, 1.50 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 21 52→€ SHIM, 1.55 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 47 52→€ 		0
----- A 000 017 47 52→€ SHIM, 1.55 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 22 52→€ SHIM, 1.60 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 48 52→€ 		0
----- A 000 017 48 52→€ SHIM, 1.60 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 23 52→€ SHIM, 1.65 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 49 52→€ 		0
----- A 000 017 49 52→€ SHIM, 1.65 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 24 52→€ SHIM, 1.70 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 50 52→€ 		0
----- A 000 017 50 52→€ SHIM, 1.70 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 25 52→€ SHIM, 1.75 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 51 52→€ 		0
----- A 000 017 51 52→€ SHIM, 1.75 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 26 52→€ SHIM, 1.80 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE

Заменено на: A 000 017 52 52→€ 		0
----- A 000 017 52 52→€ SHIM, 1.80 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 53 52→€ SHIM, 1.85 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 54 52→€ SHIM, 1.90 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
----- A 000 017 55 52→€ SHIM, 1.95 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE 		0
86 A 000 017 04 17→€ PRESSURE SPRING
IN NOZZLE HOLDER 		4
----- A 000 017 01 74→€ THRUST BOLT
IN NOZZLE HOLDER

Заменено на: A 000 017 02 74→€ 		0
87 A 000 017 02 74→€ THRUST BOLT
IN NOZZLE HOLDER 		4
----- A 000 017 00 22→€ NOZZLE HOLDER ELEMENT

Заменено на: A 000 017 01 22→€ 		0
88 A 000 017 01 22→€ NOZZLE HOLDER ELEMENT 4
89 A 000 017 05 16→€ BOX NUT
TO FIX INJECTION NOZZLE 		4
----- SEALING RING
A 8X12 DIN 7603 A1 FOR HOLLOW SCREW FOR LEAK OIL LINE AT NOZZLES 		8
----- HOLLOW SCREW
A 3 DIN 7623 FOR CONNECTION OF LEAK OIL LINE FOR LEAK OIL LINE AT NOZZLES 		4
92 A 000 017 13 12→€ INJECTION NOZZLE
IN NOZZLE HOLDER 		4
----- A 000 017 16 12→€ INJECTION NOZZLE
FOR ENGINES WITH AN ESPECIALLY STROG DIESEL KNOCK 		4
----- A 312 017 04 20→€ REPLACED BY
636 017 01 20 TOGETHER WITH 1 THREADED RING 636 017 03 03 UP TO ENGINE 5500957 		0
93 A 636 017 01 20→€ GASKET
BETWEEN NOZZLE HOLDER AND PRECHAMBER FROM ENGINE 5500958 		4
PRESSURE AND LEAK PIPE
100 A 636 070 32 33→€ PRESSURE PIPE, BENT
FOR CYLINDER 1 FROM INJECTION PUMP TO NOZZLE HOLDER 		1
101 A 636 070 33 33→€ PRESSURE PIPE, BENT
FOR CYLINDER 2 FROM INJECTION PUMP TO NOZZLE HOLDER 		1
----- A 636 070 30 33→€ REPLACED BY
636 070 34 33 TOGETHER WITH 1 PRESSURE LINE 636 070 35 33 UP TO ENGINE 7516775 		0
102 A 636 070 34 33→€ PRESSURE PIPE, BENT
FOR CYLINDER 3 FROM INJECTION PUMP TO NOZZLE HOLDER FROM ENGINE 8516776 		1
----- A 636 070 31 33→€ REPLACED BY
636 070 35 33 TOGETHER WITH 1 PRESSURE LINE 636 070 34 33 UP TO ENGINE 8516775 		0
103 A 636 070 35 33→€ PRESSURE PIPE, BENT
FOR CYLINDER 4 FROM INJECTION PUMP TO NOZZLE HOLDER FROM ENGINE 8516776 		1
104 A 636 078 02 35→€ PIPE CLAMP
FOR PRESSURE LINES 1, 2, 3 AND 4 UP TO ENGINE 4507500 		3
104 A 636 078 02 35→€ PIPE CLAMP
FOR PRESSURE LINES 1, 2, 3 AND 4 FROM ENGINE 4507501-6501468 		5
104 A 636 078 02 35→€ PIPE CLAMP
FOR PRESSURE LINES 1, 2, 3 AND 4 FROM ENGINE 6501469 		7
----- HEX. -HD. SCREW
M 5X12 DIN 933-8 G FOR PIPE CLAMP AT PRESSURE PIPE UP TO ENGINE 4507500 		3
----- HEX. -HD. SCREW
M 5X12 DIN 933-8 G FOR PIPE CLAMP AT PRESSURE PIPE FROM ENGINE 4507501-6501468 		5
----- HEX. -HD. SCREW
M 5X12 DIN 933-8 G FOR PIPE CLAMP AT PRESSURE PIPE FROM ENGINE 6501469 		7
----- LOCK WASHER
B 5 DIN 127 FOR PIPE CLAMP AT PRESSURE PIPE UP TO ENGINE 4507500 		3
----- LOCK WASHER
B 5 DIN 127 FOR PIPE CLAMP AT PRESSURE PIPE FROM ENGINE 4507501-6501468 		5
----- LOCK WASHER
B 5 DIN 127 FOR PIPE CLAMP AT PRESSURE PIPE FROM ENGINE 6501469 		7
----- HEX. NUT
M 5 DIN 934-5 S FOR PIPE CLAMP AT PRESSURE PIPE UP TO ENGINE 4507500 		3
----- HEX. NUT
M 5 DIN 934-5 S FOR PIPE CLAMP AT PRESSURE PIPE FROM ENGINE 4507501-6501468 		5
----- HEX. NUT
M 5 DIN 934-5 S FOR PIPE CLAMP AT PRESSURE PIPE FROM ENGINE 6501469 		7
----- A 636 078 00 85→€ PIPE BRACKET
FOR FUEL PIPE, CYLINDERS 1 AND 2, AT WATER PUMP

Заменено на: A 636 078 03 85→€ 		0
108 A 636 078 03 85→€ PIPE BRACKET
FOR FUEL PIPE, CYLINDERS 1 AND 2, AT WATER PUMP 		1
109 A 636 078 03 35→€ PIPE CLAMP
FOR PRESSURE PIPE 1 AND 2 AND VACUUM LINE AT WATER PUMP 		1
----- HEX. -HD.SCREW
M 5X12 DIN 933-8 G FOR PIPE CLAMP AT PIPE BRACKET AND WATER PUMP 		1
----- LOCK WASHER
B 5 DIN 127 FOR PIPE CLAMP AT PIPE BRACKET AND WATER PUMP 		1
----- HEX. NUT
M 5 DIN 934-5 S FOR PIPE CLAMP AT PIPE BRACKET AND WATER PUMP 		1
----- A 636 078 01 85→€ PIPE BRACKET
FOR FUEL PIPE, CYLINDER 1, 3 AND 4, AT EXHAUST MANIFOLD

Заменено на: A 636 078 02 85→€ 		0
113 A 636 078 02 85→€ PIPE BRACKET
FOR FUEL PIPE, CYLINDER 1, 3 AND 4, AT EXHAUST MANIFOLD UP TO ENGINE 6501468 		1
113 A 636 078 02 85→€ PIPE BRACKET
FOR FUEL PIPE, CYLINDER 1, 3 AND 4, AT EXHAUST MANIFOLD FROM ENGINE 6501469 		2
114 A 636 078 00 86→€ RUBBER PAD
FOR PRESSURE LINE, CYLINDERS 3 AND 4 FROM ENGINE 6501469 		1
----- A 636 070 10 35→€

Заменено на: A 636 070 12 35→€ 		0
----- A 636 070 11 35→€ LEAK LINE

Заменено на: A 636 070 12 35→€ 		0
115 A 636 070 12 35→€ LEAK LINE 1
----- A 636 070 00 40→€ BRACKET, T-FITTING
AT TIMING GEAR CASE COVER

Заменено на: A 636 070 01 40→€ 		0
----- A 636 070 01 40→€ BRACKET, T-FITTING
AT TIMING GEAR CASE COVER UP TO ENGINE 7507990 		1
116 A 636 070 02 40→€ BRACKET, T-FITTING
AT TIMING GEAR CASE COVER FROM ENGINE 7507991 		1
B07005Z10001.051209
[image]