| № поз. |
Номер детали |
Название/дополнительная информация |
Колич |
Версия |
|
CRANKSHAFT
|
|
----- |
A 121 030 37 01→ |
CRANKSHAFT WITH
COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS LAUCHERTHAL OPTIONAL |
1 |
|
|
----- |
A 121 030 39 01→ |
CRANKSHAFT WITH
COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS GLYCO OPTIONAL |
1 |
|
|
1 |
A 121 030 35 01→ |
CRANKSHAFT WITH
COUNTERWEIGHT AND FLYWHEEL |
1 |
|
|
2 |
A 180 031 00 52→ |
SHIM 5.45 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
1 |
|
|
----- |
A 180 031 01 52→ |
SHIM 5.60 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
1 |
|
|
----- |
A 180 031 02 52→ |
SHIM 5.75 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
1 |
|
|
----- |
A 180 031 03 52→ |
SHIM 5.90 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
1 |
|
|
----- |
A 180 031 04 52→ |
SHIM 6.05 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
1 |
|
|
3 |
|
WOODRUFF KEY
5X7,5 DIN 6888 |
1 |
|
|
4 |
A 180 052 02 03→ |
CRANKSHAFT GEAR
ON CRANKSHAFT, FRONT |
1 |
|
|
5 |
A 180 031 04 25→ |
OIL SLINGER RING
ON CRANKSHAFT, FRONT |
1 |
|
|
----- |
A 121 031 01 07→ |
REPLACED BY
121 031 03 07 TOGETHER WITH 1 SPACER RING 121 031 00 51 UP TO ENGINE 75 11543 WITH EXCEPTION OF 75 11374 TO 75 11423 |
0 |
|
|
5a |
A 121 031 03 07→ |
COUNTERWEIGHT
FROM ENGINE 75 11544 IN ADDITION MOUNTED IN 75 11374 TO 75 11423 |
1 |
|
|
5b |
A 121 031 00 51→ |
SPACER RING
FOR CRANKSHAFT, OIL SLINGER RING FROM ENGINE 75 11544 IN ADDITION MOUNTED IN 75 11374 TO 75 11423 |
1 |
|
|
6 |
|
CYLINDRICAL PIN
8 H8 X 8 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT |
1 |
|
|
7 |
|
CYLINDRICAL PIN
8 H8 X 16 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT |
1 |
|
|
----- |
A 121 030 03 05→ |
FLYWHEEL WITH
Заменено на: A 121 030 08 05→ |
0 |
|
|
8 |
A 121 030 08 05→ |
FLYWHEEL WITH |
1 |
|
|
9 |
A 121 032 00 05→ |
STARTER RING
GEAR, 108 TEETH |
1 |
|
|
10 |
A 121 031 06 71→ |
NECKED-DOWN BOLT
FOR FLYWHEEL AT CRANKSHAFT |
6 |
|
|
11 |
|
CYLINDRICAL PIN
10 H8 X 18 DIN 7 FOR FLYWHEEL AT CRANKSHAFT |
1 |
|
|
----- |
A 121 206 01 17→ |
WASHER
FOR HUB, PULLEY UP TO ENGINE 6500024 |
1 |
|
|
13 |
A 186 031 02 71→ |
COLLAR SCREW |
1 |
|
|
14 |
A 120 031 01 81→ |
SEALING RING
AT CRANKSHAFT, FRONT |
1 |
|
|
14a |
A 121 032 00 15→ |
ADJUSTING NEEDLE
FOR TOP DEAD CENTER ADJUSTMENT |
1 |
|
|
----- |
|
CYLINDER SCREW
AM 6X8 DIN 84-4 S FOR ADJUSTMENT POINTER - FIXING FROM ENGINE 8509140 |
1 |
|
|
----- |
A 121 206 00 10→ |
PULLEY
Заменено на: A 121 200 01 05→ |
0 |
|
|
15 |
A 121 200 01 05→ |
PULLEY |
1 |
|
|
16 |
|
GROOVED BEARING
6202 DIN 625 FOR DRIVE SHAFT AT CRANKSHAFT |
1 |
|
|
17 |
A 186 031 00 33→ |
LOCKING RING
FOR DRIVE SHAFT AT CRANKSHAFT |
1 |
|
|
----- |
A 121 031 00 53→ |
SPACER SLEEVE
IN CRANKSHAFT FOR GROOVED BEARING UP TO ENGINE 6510419 |
1 |
|
|
18 |
|
FABRIC SEALING RING
75X87X6 GL N 255 A FOR CRANKSHAFT SEALING IN CYLINDER CRANKCASE, REAR |
1 |
|
|
CRANKSHAFT BEARING
|
|
20 |
A 121 030 05 97→ |
SET OF
CRANKSHAFT BEARING SHELLS, GLYCO INTERIOR DIA. 70 MM = STANDARD (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 121 030 10 97→ |
SET OF
CRANKSHAFT BEARING SHELLS, VANDERVELL INTERIOR DIA. 70 MM = STANDARD (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 621 030 00 97→ |
SET OF
CRANKSHAFT BEARING SHELLS LAUCHERTHAL INTERIOR DIA. 70 MM = STANDARD (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
21 |
A 121 033 14 01→ |
CRANKSHAFT BEARING SHELL
GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER BEARIN |
4 |
|
|
----- |
A 121 033 19 01→ |
CRANKSHAFT BEARING SHELL
VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B |
4 |
|
|
----- |
A 621 033 00 01→ |
CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER |
4 |
|
|
22 |
A 121 033 14 02→ |
CRANKSHAFT BEARING SHELL
GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 121 033 19 02→ |
CRANKSHAFT BEARING SHELL
VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 621 033 00 02→ |
CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 121 030 06 97→ |
SET OF
CRANKSHAFT BEARING SHELLS GLYCO INTERIOR DIA. = 69.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 121 030 11 97→ |
SET OF
CRANKSHAFT BEARING SHELLS VANDERVELL INTERIOR DIA. = 69.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 621 030 01 97→ |
SET OF
CRANKSHAFT BEARING SHELLS LAUCHERTHAL INTERIOR DIA. = 69.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 121 033 15 01→ |
CRANKSHAFT BEARING SHELL
GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AT UPPER AND LOWER HALF FOR CENTER BEARIN |
4 |
|
|
----- |
A 121 033 20 01→ |
CRANKSHAFT BEARING SHELL
VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AT UPPER AND LOWER HALF FOR CENTER B |
4 |
|
|
----- |
A 621 033 01 01→ |
CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AT UPPER AND LOWER HALF FOR CENTER |
4 |
|
|
----- |
A 121 033 15 02→ |
CRANKSHAFT BEARING SHELL
GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 121 033 20 02→ |
CRANKSHAFT BEARING SHELL
VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 621 033 01 02→ |
CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 121 030 07 97→ |
SET OF
CRANKSHAFT BEARING SHELLS GLYCO INTERIOR DIA. 69.50 MM = REPAIR SIZE II. (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 121 030 12 97→ |
SET OF
CRANKSHAFT BEARING SHELLS VANDERVELL INTERIOR DIA. 69.50 MM = REPAIR SIZE II. (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 621 030 02 97→ |
SET OF
CRANKSHAFT BEARING SHELLS LAUCHERTHAL INTERIOR DIA. 69.50 MM = REPAIR SIZE II. (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 121 033 16 01→ |
CRANKSHAFT BEARING SHELL
GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER BEARIN |
4 |
|
|
----- |
A 121 033 21 01→ |
CRANKSHAFT BEARING SHELL
VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B |
4 |
|
|
----- |
A 621 033 02 01→ |
CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER |
4 |
|
|
----- |
A 121 033 16 02→ |
CRANKSHAFT BEARING SHELL
GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 121 033 21 02→ |
CRANKSHAFT BEARING SHELL
VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 621 033 02 02→ |
CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 121 030 08 97→ |
SET OF
CRANKSHAFT BEARING SHELLS GLYCO INTERIOR DIA. 69.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 121 030 13 97→ |
SET OF
CRANKSHAFT BEARING SHELLS VANDERVELL INTERIOR DIA. 69.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 621 030 03 97→ |
SET OF
CRANKSHAFT BEARING SHELLS LAUCHERTHAL INTERIOR DIA. 69.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 121 033 17 01→ |
CRANKSHAFT BEARING SHELL
GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER BEARIN |
4 |
|
|
----- |
A 121 033 22 01→ |
CRANKSHAFT BEARING SHELL
VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B |
4 |
|
|
----- |
A 621 033 03 01→ |
CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER |
4 |
|
|
----- |
A 121 033 17 02→ |
CRANKSHAFT BEARING SHELL
GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 121 033 22 02→ |
CRANKSHAFT BEARING SHELL
VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 621 033 03 02→ |
CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 121 030 09 97→ |
SET OF
CRANKSHAFT BEARING SHELLS GLYCO INTERIOR DIA. 69.00 MM REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 121 030 14 97→ |
SET OF
CRANKSHAFT BEARING SHELLS VANDERVELL INTERIOR DIA. 69.00 MM REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 621 030 04 97→ |
SET OF
CRANKSHAFT BEARING SHELLS LAUCHERTHAL INTERIOR DIA. 69.00 MM REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL |
1 |
|
|
----- |
A 121 033 18 01→ |
CRANKSHAFT BEARING SHELL
GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER BEARIN |
4 |
|
|
----- |
A 121 033 23 01→ |
CRANKSHAFT BEARING SHELL
VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B |
4 |
|
|
----- |
A 621 033 04 01→ |
CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER |
4 |
|
|
----- |
A 121 033 18 02→ |
CRANKSHAFT BEARING SHELL
GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 121 033 23 02→ |
CRANKSHAFT BEARING SHELL
VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
----- |
A 621 033 04 02→ |
CRANKSHAFT BEARING SHELL
LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
CONNECTING ROD
|
|
25 |
A 121 030 15 20→ |
CONNECTING ROD |
4 |
|
|
26 |
A 186 038 07 50→ |
CONNECTING ROD BUSHING |
4 |
|
|
27 |
A 121 038 03 71→ |
CONNECTING SCREW |
8 |
|
|
28 |
A 182 038 00 72→ |
NUT |
8 |
|
|
----- |
A 186 038 08 50→ |
CONNECTING ROD
BUSHING, EXTERIOR DIA. 28.5-MM REPAIR DESIGN |
4 |
|
|
----- |
A 121 038 28 11→ |
CONNECTING ROD
BEARING SHELL INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL
Заменено на: A 121 038 28 10→ |
0 |
|
|
29 |
A 121 038 28 10→ |
CONNECTING ROD
BEARING SHELL GLYCO INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 07 11→ |
CONNECTING ROD
BEARING SHELL INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL
Заменено на: A 121 038 07 10→ |
0 |
|
|
----- |
A 121 038 07 10→ |
CONNECTING ROD
BEARING SHELL LAUCHERTHAL INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 33 10→ |
CONNECTING ROD
BEARING SHELL VANDERVELL INTERIOR DIA. 52.00 MM STANDARD (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 29 11→ |
CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL
Заменено на: A 121 038 29 10→ |
0 |
|
|
----- |
A 121 038 29 10→ |
CONNECTING ROD
BEARING SHELL GLYCO INTERIOR DIA. 51.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 08 11→ |
CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL
Заменено на: A 121 038 08 10→ |
0 |
|
|
----- |
A 121 038 08 10→ |
CONNECTING ROD
BEARING SHELL LAUCHERTHAL INTERIOR DIA. 51.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 34 10→ |
CONNECTING ROD
BEARING SHELL VANDERVELL INTERIOR DIA. 51.75 MM = REPAIR SIZE I (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 30 11→ |
CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.50 MM = REPAIR SIZE II (READY FOR INSTALLATION) OPTIONAL
Заменено на: A 121 038 30 10→ |
0 |
|
|
----- |
A 121 038 30 10→ |
CONNECTING ROD
BEARING SHELL GLYCO INTERIOR DIA. 51.50 MM = REPAIR SIZE II (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 09 11→ |
CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.50 MM = REPAIR SIZE II (READY FOR INSTALLATION) OPTIONAL
Заменено на: A 121 038 09 10→ |
0 |
|
|
----- |
A 121 038 09 10→ |
CONNECTING ROD
BEARING SHELL LAUCHERTHAL INTERIOR DIA. 51.50 MM = REPAIR SIZE II (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 35 10→ |
CONNECTING ROD
BEARING SHELL VANDERVELL INTERIOR DIA. 51.50 MM = REPAIR SIZE II (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 31 11→ |
CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL
Заменено на: A 121 038 31 10→ |
0 |
|
|
----- |
A 121 038 31 10→ |
CONNECTING ROD
BEARING SHELL GLYCO INTERIOR DIA. 51.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 10 11→ |
CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL
Заменено на: A 121 038 10 10→ |
0 |
|
|
----- |
A 121 038 10 10→ |
CONNECTING ROD
BEARING SHELL LAUCHERTHAL INTERIOR DIA. 51.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 36 10→ |
CONNECTING ROD
BEARING SHELL VANDERVELL INTERIOR DIA. 51.25 MM = REPAIR SIZE III (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 32 11→ |
CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.00 MM = REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL
Заменено на: A 121 038 32 10→ |
0 |
|
|
----- |
A 121 038 32 10→ |
CONNECTING ROD
BEARING SHELL GLYCO INTERIOR DIA. 51.00 MM = REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 11 11→ |
CONNECTING ROD
BEARING SHELL INTERIOR DIA. 51.00 MM = REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL
Заменено на: A 121 038 11 10→ |
0 |
|
|
----- |
A 121 038 11 10→ |
CONNECTING ROD
BEARING SHELL LAUCHERTHAL INTERIOR DIA. 51.00 MM = REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
----- |
A 121 038 37 10→ |
CONNECTING ROD
BEARING SHELL VANDERVELL INTERIOR DIA. 51.00 MM = REPAIR SIZE IV (READY FOR INSTALLATION) OPTIONAL |
8 |
|
|
PISTON
|
|
34 |
A 121 030 02 17→ |
PISTON WITH
PISTON PIN AND PISTON RINGS MAKE MAHLE FOR CYLINDER DIA.85.00 MM = STANDARD OPTIONAL |
4 |
|
|
----- |
A 121 030 08 17→ |
PISTON WITH
PISTON PIN AND PISTON RINGS MAKE NÜRAL FOR CYLINDER DIA.85.00 MM = STANDARD OPTIONAL |
4 |
|
|
35 |
A 001 037 38 16→ |
COMPRESSION RING
FOR GROOVE I |
4 |
|
|
36 |
A 001 037 43 16→ |
TAPERED RING
FOR GROOVE II |
4 |
|
|
37 |
A 000 037 00 17→ |
NOVIX STEPPED RING
FOR GROOVE III |
4 |
|
|
38 |
A 000 037 29 18→ |
NOVIX SLOTTED RING
FOR GROOVE IV |
4 |
|
|
39 |
|
PISTON PIN
D 25 X 18 X 72 DIN 73121 K |
4 |
|
|
40 |
|
WIRE SNAP RING
A 25 DIN 73123 |
8 |
|
|
----- |
A 121 030 03 17→ |
PISTON WITH
PISTON PIN AND PISTON RINGS MAKE MAHLE FOR CYLINDER DIA. 85.25 MM REPAIR SIZE I. OPTIONAL |
4 |
|
|
----- |
A 121 030 09 17→ |
PISTON WITH
PISTON PIN AND PISTON RINGS MAKE NÜRAL FOR CYLINDER DIA. 85.25 MM REPAIR SIZE I. OPTIONAL |
4 |
|
|
----- |
A 001 037 39 16→ |
COMPRESSION RING
FOR GROOVE I |
4 |
|
|
----- |
A 001 037 44 16→ |
TAPERED RING
FOR GROOVE II |
4 |
|
|
----- |
A 000 037 11 17→ |
NOVIX STEPPED RING
FOR GROOVE III |
4 |
|
|
----- |
A 000 037 69 18→ |
NOVIX SLOTTED RING
FOR GROOVE IV |
4 |
|
|
----- |
|
PISTON PIN
D 25 X 18 X 72 DIN 73121 K |
4 |
|
|
----- |
|
WIRE SNAP RING
A 25 DIN 73123 |
8 |
|
|
----- |
A 121 030 04 17→ |
PISTON WITH
PISTON PIN AND PISTON RINGS MAKE MAHLE FOR CYLINDER DIA. 85.50 MM = REPAIR SIZE II. OPTIONAL |
4 |
|
|
----- |
A 121 030 10 17→ |
PISTON WITH
PISTON PIN AND PISTON RINGS MAKE NÜRAL FOR CYLINDER DIA. 85.50 MM = REPAIR SIZE II. OPTIONAL |
4 |
|
|
----- |
A 001 037 40 16→ |
COMPRESSION RING
FOR GROOVE I |
4 |
|
|
----- |
A 001 037 45 16→ |
TAPERED RING
FOR GROOVE II |
4 |
|
|
----- |
A 000 037 01 17→ |
NOVIX STEPPED RING
FOR GROOVE III |
4 |
|
|
----- |
A 000 037 36 18→ |
NOVIX SLOTTED RING
FOR GROOVE IV |
4 |
|
|
----- |
|
PISTON PIN
D 25 X 18 X 72 DIN 73121 K |
4 |
|
|
----- |
|
WIRE SNAP RING
A 25 DIN 73123 |
8 |
|
|
----- |
A 121 030 05 17→ |
PISTON WITH
PISTON PIN AND PISTON RINGS, MAKE MAHLE FOR CYLINDER DIA. 86.00 MM = REPAIR SIZE III. OPTIONAL |
4 |
|
|
----- |
A 121 030 11 17→ |
PISTON WITH
PISTON PIN AND PISTON RINGS, MAKE NÜRAL FOR CYLINDER DIA. 86.00 MM = REPAIR SIZE III. OPTIONAL |
4 |
|
|
----- |
A 001 037 41 16→ |
COMPRESSION RING
FOR GROOVE I |
4 |
|
|
----- |
A 001 037 46 16→ |
COMPRESSION RING
FOR GROOVE II |
4 |
|
|
----- |
A 000 037 02 17→ |
NOVIX STEPPED RING
FOR GROOVE III |
4 |
|
|
----- |
A 000 037 37 18→ |
NOVIX SLOTTED RING
FOR GROOVE IV |
4 |
|
|
----- |
|
PISTON PIN
D 25 X 18 X 72 DIN 73121 K |
4 |
|
|
----- |
|
WIRE SNAP RING
A 25 DIN 73123 |
8 |
|
|
----- |
A 121 030 06 17→ |
PISTON WITH
PISTON PIN AND PISTON RINGS MAKE MAHLE FOR CYLINDER DIA. 86.50 MM REPAIR SIZE IV. OPTIONAL |
4 |
|
|
----- |
A 121 030 12 17→ |
PISTON WITH
PISTON PIN AND PISTON RINGS, MAKE NÜRAL FOR CYLINDER DIA. 86.50 MM REPAIR SIZE IV. OPTIONAL |
4 |
|
|
----- |
A 001 037 42 16→ |
COMPRESSION RING
FOR GROOVE I |
4 |
|
|
----- |
A 001 037 47 16→ |
TAPERED RING
FOR GROOVE II |
4 |
|
|
----- |
A 000 037 03 17→ |
NOVIX STEPPED RING
FOR GROOVE III |
4 |
|
|
----- |
A 000 037 38 18→ |
NOVIX SLOTTED RING
FOR GROOVE IV |
4 |
|
|
----- |
|
PISTON PIN
D 25 X 18 X 72 DIN 73121 K |
4 |
|
|
----- |
|
WIRE SNAP RING
A 25 DIN 73123 |
8 |
|
![[image]](https://img.nemcy-zdes.ru/mb/BM_IMAGES_ARC/B03003Z12001.051209.png)
