| № поз. |
Номер детали |
Название/дополнительная информация |
Колич |
Версия |
|
ENGINE
|
|
----- |
A 121 010 15 02→ |
ENGINE, COMPLETE
WITHOUT STARTER MOTOR, FAN, CLUTCH AND TRANSMISSION |
0 |
LM |
|
----- |
A 121 010 16 02→ |
ENGINE, COMPLETE
WITHOUT STARTER MOTOR, FAN, CLUTCH AND TRANSMISSION |
0 |
RM |
|
----- |
A 121 010 78 00→ |
ENGINE, COMPLETE
WITH SHORT-RANGE INTERFERENCE SUPPRESSION WITHOUT STARTER MOTOR, FAN, CLUTCH AND TRANSMISSION SPECIAL REQUEST INSTALLATI |
0 |
LM |
|
----- |
A 121 010 76 00→ |
ENGINE, COMPLETE
WITHOUT INTERFERENCE SUPPRESSION WITHOUT STARTER MOTOR, FAN, CLUTCH AND TRANSMISSION SPECIAL REQUEST INSTALLATION OF A G |
0 |
LM |
|
----- |
A 121 010 79 00→ |
ENGINE, COMPLETE
WITH SHORT-RANGE INTERFERENCE SUPPRESSION WITHOUT STARTER MOTOR, FAN, CLUTCH AND TRANSMISSION SPECIAL REQUEST INSTALLATI |
0 |
RM |
|
----- |
A 121 010 77 00→ |
ENGINE, COMPLETE
WITHOUT INTERFERENCE SUPPRESSION WITHOUT STARTER MOTOR, FAN, CLUTCH AND TRANSMISSION SPECIAL REQUEST INSTALLATION OF A G |
0 |
RM |
|
----- |
A 121 010 74 00→ |
ENGINE, COMPLETE
WITHOUT STARTER MOTOR, FAN, CLUTCH AND TRANSMISSION SPECIAL REQUEST; FOR CHASSIS WITHOUT BODY AND FOR AMBULANCES |
0 |
LM |
|
----- |
A 121 010 75 00→ |
ENGINE, COMPLETE
WITHOUT STARTER MOTOR, FAN, CLUTCH AND TRANSMISSION SPECIAL REQUEST; FOR CHASSIS WITHOUT BODY AND FOR AMBULANCES |
0 |
RM |
|
----- |
A 121 010 21 02→ |
ENGINE, COMPLETE
WITHOUT STARTER MOTOR, FAN, CLUTCH AND TRANSMISSION SPECIAL REQUEST; WITH LOW COMPRESSION (7.0:1) FOR REGIONS WITH BAD F |
0 |
LM |
|
----- |
A 121 010 22 02→ |
ENGINE, COMPLETE
WITHOUT STARTER MOTOR, FAN, CLUTCH AND TRANSMISSION SPECIAL REQUEST; WITH LOW COMPRESSION (7.0:1) FOR REGIONS WITH BAD F |
0 |
RM |
|
CYLINDER CRANKCASE
|
|
1 |
A 121 010 35 08→ |
CYLINDER CRANKCASE |
1 |
|
|
----- |
B 25 N 59 a→ |
LOCKING PLATE
FOR CORE HOLES UP TO ENGINE |
1 |
|
|
----- |
B 30 N 59 a→ |
LOCKING PLATE
FOR CORE HOLES UP TO ENGINE |
2 |
|
|
----- |
B 35 N 59 a→ |
LOCKING PLATE
FOR CORE HOLES UP TO ENGINE |
1 |
|
|
----- |
B 40 N 59 a→ |
LOCKING PLATE
FOR CORE HOLES UP TO ENGINE |
2 |
|
|
----- |
|
LOCKING SCREW
M 30X1,5 DIN 906 FOR CORE HOLES FROM ENGINE |
4 |
|
|
----- |
|
LOCKING SCREW
M 38X1,5 DIN 906 FOR CORE HOLES FROM ENGINE |
2 |
|
|
5 |
A 121 011 07 11→ |
CRANKSHAFT BEARING CAP
FOR 1ST AND 3RD CRANKSHAFT BEARING |
2 |
|
|
6 |
A 121 010 09 23→ |
CRANKSHAFT BEARING
CAP WITH TIGHTENING PIN FOR 2ND CRANKSHAFT BEARING |
1 |
|
|
7 |
A 121 991 00 41→ |
TIGHTENING PIN
FOR 2ND CRANKSHAFT BEARING |
4 |
|
|
8 |
A 121 011 00 52→ |
GUARD PLATE HALF 2.00 MM
STANDARD FOR CRANKSHAFT BEARING CAP |
2 |
|
|
----- |
A 121 011 01 52→ |
GUARD PLATE
HALF 2.05-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
A 121 011 02 52→ |
GUARD PLATE
HALF 2,10-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
A 121 011 03 52→ |
GUARD PLATE
HALF 2.15-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
A 121 011 04 52→ |
GUARD PLATE
HALF 2.20-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
A 121 011 05 52→ |
GUARD PLATE
HALF 2.25-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
A 121 011 06 52→ |
GUARD PLATE
HALF 2.30-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
A 121 011 07 52→ |
GUARD PLATE
HALF 2.35-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
10 |
|
WASHER
B 12 DIN 137 FOR CRANKSHAFT BEARING CAP AT CYLINDER CRANKCASE |
6 |
|
|
11 |
|
HEX. -HD. SCREW
M 12X75 DIN 931-10 K FOR CRANKSHAFT BEARING CAP AT CYLINDER CRANKCASE |
5 |
|
|
12 |
A 121 011 00 71→ |
SCREW
FOR CRANKSHAFT BEARING CAP AT CYLINDER CRANKCASE |
1 |
|
|
----- |
|
CYLINDR. PIN
10 M6X16 DIN 7 FOR CRANKSHAFT BEARING CAP AT CYLINDER CRANKCASE |
3 |
|
|
----- |
|
CYLINDR. PIN
8 M6X16 DIN 7 FOR CRANKSHAFT BEARING CAP AT CYLINDER CRANKCASE |
3 |
|
|
----- |
B 25 N 59 a→ |
LOCKING PLATE
FOR LOCKING TIMING MARK HOLE AT CYLINDER CRANKCASE, REAR UP TO ENGINE |
1 |
|
|
16 |
A 180 991 00 60→ |
DOWEL PIN
FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE |
1 |
|
|
17 |
A 180 991 01 60→ |
DOWEL PIN
FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE |
1 |
|
|
----- |
|
SCREW PLUG
M 16X1,5 DIN 906-4 S FOR OIL DUCT, FRONT AND REAR |
3 |
|
|
22 |
A 127 184 01 56→ |
SCREW PLUG
FOR OIL DUCT, FRONT AND REAR |
1 |
|
|
----- |
|
SEALING RING
A 24X30 DIN 7603 A1 FOR OIL DUCT, FRONT AND REAR |
1 |
|
|
----- |
|
CYLINDR. PIN
10 M6X14 DIN 7 FOR CYLINDER HEAD AT CYLINDER CRANKCASE |
2 |
|
|
----- |
|
STUD BOLT
M 8X30 DIN 939-10 K FOR TIGHTENING SCREW AT CYLINDER CRANKCASE |
0 |
LM |
|
----- |
|
STUD BOLT
M 10X18 DIN 939-5 S FOR SUPPORT, GENERATOR |
2 |
|
|
30 |
A 121 070 03 24→ |
MOUNTING SUPPORT |
1 |
|
|
----- |
|
WASHER
6,4 DIN 125 FOR SUPPORT, DOUBLE LEVER, AT CYLINDER CRANKCASE |
3 |
|
|
----- |
|
HEX. -HD. SCREW
M 6X15 DIN 933-8 G FOR SUPPORT, DOUBLE LEVER, AT CYLINDER CRANKCASE |
3 |
|
|
35 |
|
DRAIN VALVE
CM 14X1,5 K DIN 71401 IN CYLINDER CRANKCASE |
1 |
|
|
39 |
A 180 011 01 33→ |
LOCKING COVER
IN CYLINDER CRANKCASE, FRONT |
1 |
|
|
40 |
A 180 011 01 79→ |
GASKET
FOR LOCKING COVER AT CYLINDER CRANKCASE |
1 |
|
|
----- |
|
HEX. -HD. SOCKET SCREW
M 6X12 DIN 912-6 G FOR LOCKING COVER AT CYLINDER CRANKCASE |
4 |
|
|
----- |
A 180 052 10 06→ |
BUSHING
FOR INTERMEDIATE SHAFT, REAR SEE ALSO GROUP 05 |
1 |
|
|
----- |
A 180 150 01 07→ |
BEARING WITH BUSHING
FOR IGNITION DISTRIBUTOR AND OIL PUMP DRIVE SEE ALSO GROUP 15 |
1 |
|
|
----- |
A 186 991 00 55→ |
LOCKING PIN
FOR FABRIC SEALING RING |
1 |
|
|
----- |
|
SEALING RING
A 6X10 DIN 7603 A1 FOR LOCKING OF THROUGH HOLE FOR SUPPORT "SERVO" ENGINE |
1 |
|
|
----- |
|
HEX. -HD. SCREW
M 6X10 DIN 933-8 G FOR LOCKING OF THROUGH HOLE FOR SUPPORT "SERVO" ENGINE |
1 |
|
|
----- |
|
SEALING RING
A 8X12 DIN 7603 A1 FOR LOCKING OF THE STUD BOLT HOLE CARBURETOR REGULATION |
1 |
|
|
----- |
|
HEX. -HD. SCREW
M 8X10 DIN 933-8 G FOR LOCKING OF THE STUD BOLT HOLE CARBURETOR REGULATION |
1 |
|
|
46 |
A 180 011 11 05→ |
INTERMEDIATE PLATE
FITTED HOLE DIA. 12 MM FOR CYLINDER CRANKCASE, STARTER MOTOR |
1 |
|
|
----- |
|
HEX. -HD. SCREW
M 10X15 DIN 933-8 G FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE |
3 |
|
|
----- |
|
SPRING WASHER
B 10 DIN 137 FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE |
3 |
|
|
OIL PAN
|
|
50 |
A 121 010 10 13→ |
OIL PAN |
1 |
|
|
----- |
A 186 991 00 55→ |
LOCKING PIN
FOR FABRIC SEALING RING |
1 |
|
|
51 |
A 180 010 00 66→ |
GUIDE TUBE
IN OIL PAN FOR OIL DIPSTICK |
1 |
|
|
53 |
A 198 997 00 40→ |
SEALING RING
FOR BREATHER FILTER |
1 |
|
|
55 |
A 121 010 00 72→ |
OIL DIPSTICK
WITH BREATHER FILTER |
1 |
|
|
----- |
|
SEALING RING
C 26 X 32 DIN 7603 CU. ASB. FOR OIL DRAIN, OIL PAN |
1 |
|
|
57 |
A 136 997 12 30→ |
SCREW PLUG
FOR OIL DRAIN, OIL PAN |
1 |
|
|
----- |
|
WASHER
6,4 DIN 433 FOR OIL PAN AT CYLINDER CRANKCASE |
18 |
|
|
----- |
|
HEX. -HD. SOCKET SCREW
M 6X15 DIN 912-6 G FOR OIL PAN AT CYLINDER CRANKCASE |
16 |
|
|
----- |
|
HEX. -HD. SOCKET SCREW
M 6X60 DIN 912-8 G FOR OIL PAN AT CYLINDER CRANKCASE |
2 |
|
|
----- |
|
WASHER
8,4 DIN 433 FOR OIL PAN AT CYLINDER CRANKCASE |
4 |
|
|
----- |
|
HEX. -HD. SOCKET SCREW
M 8X30 DIN 912-8 G FOR OIL PAN AT CYLINDER CRANKCASE |
2 |
|
|
----- |
|
HEX. -HD. SOCKET SCREW
M 8X90 DIN 912-8 G FOR OIL PAN AT CYLINDER CRANKCASE |
2 |
|
![[image]](https://img.nemcy-zdes.ru/mb/BM_IMAGES_ARC/B01001Z13001.051209.png)
