Mercedes

The best or nothing

К сожалению, мы не смогли определить Ваш город (ip=3.136.17.119)
Пожалуйста, укажите его самостоятельно

Поиск по идентификационному номеру VIN

Поиск по номеру детали

Автозапчасти Mercedes

Каталог Mercedes→Категория «Легковой а/м»→Раздел «M - двигатель»→Модельный ряд «TYP M 180.III BM 180.924»→Группа 07 - CARBURETOR

Группа 07 → CARBURETOR

Подгруппа 005 → CARBURETOR

№ поз.	Номер детали	Название/дополнительная информация	Колич	Версия
CARBURETOR
-----	A 000 071 68 01→	CARBURETOR II, Заменено на: A 000 071 74 01→	0
I	A 000 071 74 01→	CARBURETOR II,	1
-----	A 000 071 69 01→	CARBURETOR I, REAR 32 PAJTA Заменено на: A 000 071 73 01→	0
II	A 000 071 73 01→	CARBURETOR I, REAR 32 PAJTA	1
1	A 000 071 04 70→	SETSCREW FOR TEST INSTRUMENT CONNECTION	2
-----	A 000 071 00 70→	SETSCREW FOR CARBURETOR I	1
2	A 000 071 17 11→	THROTTLE VALVE SHAFT, 1ST BARREL IN THROTTLE VALVE CASE	2
-----	A 000 071 04 10→	THROTTLE VALVE 8DEGREES 1ST BARREL IN THROTTLE VALVE CASE Заменено на: A 000 071 07 10→	0
3	A 000 071 07 10→	THROTTLE VALVE 8DEGREES 1ST BARREL IN THROTTLE VALVE CASE	2
4	A 000 071 36 71→	LENS-HD. COUNTERSUNK SCREW FOR MOUNTING OF THROTTLE VALVE, 1ST BARREL	4
-----	A 000 071 13 12→	SUPPORT UP TO ENGINE 8504580	0	M
-----	A 000 071 13 12→	SUPPORT UP TO ENGINE 8501748	0	A
-----	A 000 070 06 21→	REPLACED BY 000 070 11 21 TOGETHER WITH 2 FOLLOWER LEVER 000 070 12 21 UP TO ENGINE 8504580	0	M
-----	A 000 070 06 21→	REPLACED BY 000 070 11 21 TOGETHER WITH 2 FOLLOWER LEVER 000 070 12 21 UP TO ENGINE 8501748	0	A
6	A 000 070 11 21→	THROTTLE LEVER WITH SUPPORT FROM ENGINE 8504581	0	M
6	A 000 070 11 21→	THROTTLE LEVER WITH SUPPORT FROM ENGINE 8501749	0	A
-----	A 000 070 07 21→	FOLLOWER LEVER, FOLLOWER ROD AND DRAG LINK UP TO ENGINE 8504580	0	M
-----	A 000 070 07 21→	FOLLOWER LEVER, FOLLOWER ROD AND DRAG LINK UP TO ENGINE 8501748	0	A
7	A 000 070 12 21→	FOLLOWER LEVER, FOLLOWER ROD AND DRAG LINK FROM ENGINE 8504581	0	M
7	A 000 070 12 21→	FOLLOWER LEVER, FOLLOWER ROD AND DRAG LINK FROM ENGINE 8501749	0	A
7a	A 000 072 00 53→	SPACER BUSHING FOR THROTTLE LEVER	2
7b	A 000 071 08 15→	SPRING BETWEEN THROTTLE VALVE LEVER AND FOLLOWER LEVER	2
8	A 000 071 04 22→	LEVER FOR MECHANICAL PUMP	2
14	A 000 071 01 76→	SPACER WASHER BETWEEN THROTTLE VALVE HOUSING, SUPPORT AND LEVER	6
16	A 000 071 04 72→	HEX. NUT FOR THROTTLE VALVE SHAFT, 1ST BARREL	4
17	A 000 994 02 10→	LOCKING WASHER FOR HEX. NUT AT THROTTLE VALVE LEVER	2
19	A 000 071 18 11→	VACUUM VALVE SHAFT, FOR THROTTLE VALVE	2
20	A 000 071 12 10→	VACUUM VALVE 17DEGREES IN THROTTLE VALVE HOUSING	2
21	A 000 071 55 71→	LENS-HD. COUNTERSUNK SCREW FOR VACUUM VALVE MOUNTING, 2ND BARREL WITH BORE FOR SECURING OF SCREW	4
23	A 000 071 01 76→	SPACER WASHER FOR VACUUM VALVE SHAFT BETWEEN HOUSING AND COUNTERWEIGHT LEVER	2
24	A 000 071 00 62→	WASHER FOR VACUUM VALVE SHAFT	2
25	A 000 071 04 72→	HEX. NUT FOR VACUUM VALVE SHAFT	2
26	A 000 071 42 71→	MIXTURE CONTROL SCREW	2
27	A 000 071 12 16→	PRESSURE SPRING FOR IDLING RUN MIXTURE CONTROL SCREW	2
28	A 000 071 43 71→	MOUNTING SCREW FOR THROTTLE VALVE HOUSING AT FLOAT CHAMBER	8
-----	A 000 990 05 47→	REPLACED BY 6 DIN 7980 FOR THROTTLE VALVE HOUSING AT FLOAT CHAMBER	0
29		LOCK WASHER 6 DIN 7980 FOR THROTTLE VALVE HOUSING AT FLOAT CHAMBER	8
31	A 000 071 19 80→	INSULATING FLANGE BETWEEN THROTTLE VALVE HOUSING AND FLOAT CHAMBER	2
33	A 000 071 01 57→	COUNTERWEIGHT	2
34	A 000 071 21 22→	LEVER FOR COUNTERWEIGHT	2
-----	A 000 071 45 71→	LENS-HD. COUNTERSUNK SCREW FOR LEVER AT COUNTERWEIGHT Заменено на: A 000 071 55 71→	0
35a	A 000 071 55 71→	LENS-HD. COUNTERSUNK SCREW FOR LEVER AT COUNTERWEIGHT	2
35b		TOOTHED WASHER V 4, 3 DIN 6797 FOR LEVER AT COUNTERWEIGHT	2
36	A 000 071 22 22→	LEVER FOR SHOCK ABSORBER	2
37a	A 000 071 07 62→	WASHER FOR LEVER	2
37b	A 136 072 00 50→	BUSHING FOR LEVER	2
37c	A 000 071 35 71→	LENS-HD. COUNTERSUNK SCREW FOR LEVER AT COUNTERWEIGHT	2
37d		TOOTHED WASHER V 4,3 DIN 6797 FOR LEVER AT COUNTERWEIGHT	2
38	A 000 070 01 67→	SHOCK ABSORBER, COMPLETE	2
40a	A 000 071 69 71→	HEX. -HD. SCREW FOR OIL FILLING IN	2
40b		SEALING RING A 4X8 DIN 7603 FIBER	2
42	A 000 071 00 91→	BELLOWS FOR PUSH ROD, CYLINDER	2
48a		WASHER 4, 3 DIN 125 FOR SHOCK ABSORBER AND LEVER	4
48b		COTTER PIN 1, 5X10 DIN 94 FOR SHOCK ABSORBER AND LEVER	4
-----	A 000 071 44 71→	HEX. -HD. SCREW FOR SHOCK ABSORBER AT FLOAT CHAMBER Заменено на: A 000 071 54 71→	0
49a	A 000 071 54 71→	HEX. -HD. SCREW FOR SHOCK ABSORBER AT FLOAT CHAMBER	2
49b		LOCK WASHER B 5 DIN 127 FOR SHOCK ABSORBER AT FLOAT CHAMBER	2
52	A 000 071 08 43→	FLOAT	2
53	A 000 071 03 77→	SHAFT FOR FLOAT	2
54	A 000 071 19 11→	THROTTLE VALVE SHAFT, 2ND BARREL	2
55a	A 000 071 11 10→	THROTTLE VALVE 17DEGREES, 2ND BARREL FOR FLOAT CHAMBER	2
55b	A 000 071 36 71→	LENS-HD. COUNTERSUNK SCREW FOR THROTTLE VALVE, 2ND BARREL	4
57a	A 000 071 01 76→	SPACER WASHER FOR THROTTLE VALVE SHAFT, 2ND BARREL, BETWEEN HOUSING AND FOLLOWER LEVER	2
57b	A 000 071 04 72→	HEX. NUT FOR THROTTLE VALVE SHAFT, 2ND BARREL	2
58	A 000 071 06 22→	STOP LEVER ON THROTTLE VALVE SHAFT, 2ND BARREL	2
59	A 000 071 04 53→	SPACER BUSHING BETWEEN FLOAT CHAMBER AND STOP LEVER	2
60	A 000 071 08 72→	HEX. NUT FOR THROTTLE VALVE SHAFT, 2ND BARREL	2
61a	A 000 071 19 42→	VENTURI TUBE, SIZE 23, 1ST BARREL	2
61b	A 000 071 12 42→	VENTURI TUBE, SIZE 27, 2ND BARREL	2
62	A 000 071 32 71→	MOUNTING SCREW FOR VENTURI TUBE	4
63	A 000 071 08 83→	MIXING TUBE SUPPORT	2
63a	A 000 071 03 20→	BALL FOR MIXING TUBE SUPPORT	2
64	A 000 071 10 49→	MIXING TUBE	2
65a	A 000 071 01 34→	COMPENSATING NOZZLE, SIZE 200, 1ST BARREL	2
65b	A 000 071 37 34→	COMPENSATING NOZZLE WITH MIXING TUBE, SIZE 190 TYPE C, 2ND BARREL	2
66	A 000 071 05 41→	MAIN NOZZLE	2
67	A 000 071 04 80→	SEALING RING FOR MAIN NOZZLE HOLDER, 1ST BARREL	2
68	A 000 071 31 35→	MAIN NOZZLE, SIZE 125, 1ST BARREL	2
68a	A 000 071 54 35→	MAIN NOZZLE, SIZE 130, 2ND BARREL	2
-----	A 000 071 57 35→	MAIN NOZZLE, SIZE 112.5 1ST BARREL (CONTROL NOZZLE) SPECIAL REQUEST - FOR COUNTRIES HIGHER THAN 2,000 M ABOVE SEA-LEVEL	2
-----	A 000 071 29 35→	MAIN NOZZLE, SIZE 115 1ST BARREL (CONTROL NOZZLE) SPECIAL REQUEST - FOR COUNTRIES HIGHER THAN 2,000 M ABOVE SEA-LEVEL	2
-----	A 000 071 32 35→	MAIN NOZZLE, SIZE 120 1ST BARREL (CONTROL NOZZLE) SPECIAL REQUEST - FOR COUNTRIES HIGHER THAN 2,000 M ABOVE SEA-LEVEL	2
-----	A 000 071 56 35→	MAIN NOZZLE, SIZE 117.5 1ST BARREL (CONTROL NOZZLE) SPECIAL REQUEST - FOR COUNTRIES HIGHER THAN 2,000 M ABOVE SEA-LEVEL	2
-----	A 000 072 01 05→	HEIGHT REGULATOR WITH DIAPHRAGM, 1ST BARREL WITHOUT MAIN NOZZLE SPECIAL REQUEST	2
68b	A 000 071 05 60→	SEALING RING FOR MAIN NOZZLE, 2ND BARREL	2
69	A 000 071 19 36→	IDLING NOZZLE, SIZE 47.5, 1ST BARREL	2
-----	A 000 071 02 39→	IDLING NOZZLE, SIZE 1.2, 1ST BARREL UP TO ENGINE 6503595	2
70	A 000 071 05 39→	IDLING NOZZLE, SIZE 1.8, 1ST BARREL FROM ENGINE 6503594	2
71	A 000 071 13 37→	STARTER FUEL NOZZLE, SIZE 100	2
72	A 000 071 05 60→	SEALING RING FOR STARTER FUEL NOZZLE	2
73	A 000 071 04 86→	PUMP NOZZLE, SIZE 80	2
74	A 000 071 05 60→	SEALING RING FOR PUMP NOZZLE	2
75a	A 000 071 01 70→	SETSCREW INSTEAD OF 2ND IDLING NOZZLE UP TO ENGINE 7511272	2
75b	A 000 071 02 70→	SETSCREW BELOW MAIN NOZZLE, 2ND BARREL UP TO ENGINE 7511272	2
76a	A 000 071 00 70→	SETSCREW INSTEAD OF 2ND IDLING NOZZLE UP TO ENGINE 7511272	2
76b	A 000 071 03 70→	SETSCREW LEFT BESIDE STARTER MOTOR UP TO ENGINE 7511272	2
77	A 000 070 01 46→	BALL VALVE	2
78	A 000 071 01 09→	STRAINER FOR BALL VALVE	2
79	A 000 071 05 60→	SEALING RING FOR BALL VALVE	2
81	A 000 070 07 73→	INJECTION TUBE	2
82	A 000 071 05 80→	GASKET 0.5 MM THICK	2
83	A 000 071 35 71→	LENS-HD. COUNTERSUNK SCREW FOR MOUNTING OF INJECTION TUBE	2
89	A 000 071 66 71→	IDLE RUN ADJUSTING SCREW	2
90	A 000 071 12 16→	PRESSURE SPRING FOR IDLE RUN ADJUSTING SCREW	2
91	A 000 070 08 52→	DIAPHRAGM PUMP	2
93	A 000 073 02 05→	DIAPHRAGM	2
94	A 000 071 05 16→	SPRING DIAPHRAGM	2
95	A 000 073 02 46→	VALVE BORED	2
96	A 000 073 00 57→	VALVE SPRING	2
102	A 000 071 40 71→	LENS-HD. COUNTERSUNK SCREW FOR VALVE AT LOWER PART	4
108	A 000 071 18 80→	GASKET BETWEEN DIAPHRAGM AND FLOAT CHAMBER	2
109	A 000 071 41 71→	CYLINDRICAL HEAD SCREW FOR DIAPHRAGM PUMP AT CARBURETOR HOUSING	8
110		LOCK WASHER B 4 DIN 127 FOR DIAPHRAGM PUMP AT CARBURETOR HOUSING	8
111	A 000 070 02 76→	CONNECTING ROD BETWEEN PUMP LEVER AND TRANSMITTING LEVER	2
112	A 000 071 12 24→	CONNECTING ROD	2
113	A 000 071 06 15→	SPRING FOR CONNECTING ROD	2
114		WASHER 4, 3 DIN 433 FOR CONNECTING ROD	2
115		COTTER PIN 1, 5X10 DIN 94 FOR CONNECTING ROD	2
116	A 000 071 06 72→	NUT FOR CONNECTING ROD	2
117	A 000 071 07 72→	HEX. NUT FOR CONNECTING ROD	2
-----	A 000 071 09 28→	CHOKE BODY	2
132	A 000 071 70 71→	CYLINDRICAL HEAD SCREW FOR MOUNTING OF CHOKE BODY	8
133		LOCK WASHER B 4 DIN 127 FOR MOUNTING OF CHOKE BODY	8
136	A 000 070 00 40→	BOWDEN CABLE BRACKET, CARBURETOR I, REAR	1
136a	A 000 072 00 40→	BOWDEN CABLE BRACKET	1
136b	A 000 072 00 41→	CLAMP	1
136c	A 000 071 44 71→	HEX. -HD. SCREW	1
136d		LOCK WASHER B 5 DIN 127	1
136e	A 000 071 13 72→	HEX. NUT	1
137	A 000 072 01 40→	BRACKET AT CARBURETOR II FRONT	1
138	A 000 990 18 20→	CYLINDRICAL HEAD SCREW FOR BOWDEN CABLE BRACKET AND BRACKET AT CARBURETOR	4
139		LOCK WASHER B 4 DIN 127 FOR BOWDEN CABLE BRACKET AND BRACKET AT CARBURETOR	4
140	A 000 071 14 30→	STARTER TURN SWITCH	2
140a	A 000 072 00 23→	STOP PIECE	2
141	A 000 070 08 21→	STARTER LEVER	2
142	A 000 070 09 21→	ANGULAR LEVER, WITH RUBBER BUSHING REAR CARBURETOR I	1
142a	A 000 070 10 21→	ANGULAR LEVER FRONT CARBURETOR II	1
143a		WASHER 6, 4 DIN 125 FOR ANGULAR LEVER	2
143b		COTTER PIN 1, 5X10 DIN 94 FOR ANGULAR LEVER	2
144	A 000 071 73 71→	CLAMPING SCREW AT ANGULAR LEVER, CARBURETOR I	1
146		WASHER 5X10X2 DIN 988 FOR CLAMPING SCREW AT ANGULAR LEVER, CARBURETOR I	2
147	A 000 071 13 72→	HEX. NUT FOR CLAMPING SCREW AT ANGULAR LEVER, CARBURETOR I	1
148	A 000 071 13 24→	CONNECTING ROD BETWEEN STARTER LEVER AND ANGULAR LEVER	2
149	A 000 071 00 62→	WASHER FOR CHOKE SHAFT	2
150	A 000 071 04 72→	HEX. NUT FOR CHOKE SHAFT	2
151	A 000 071 19 04→	CARBURETOR COVER	2
152	A 000 071 20 80→	GASKET FOR CARBURETOR COVER	2
156	A 000 071 01 44→	FLOAT NEEDLE VALVE	2
157	A 000 997 28 40→	SEALING RING OPTIONAL FOR FLOAT NEEDLE VALVE	2
-----	A 000 997 81 40→	SEALING RING OPTIONAL FOR FLOAT NEEDLE VALVE	2
-----	A 000 997 82 40→	SEALING RING OPTIONAL FOR FLOAT NEEDLE VALVE	2
-----	A 000 997 83 40→	SEALING RING OPTIONAL FOR FLOAT NEEDLE VALVE	2
161		THREADED NIPPLE 6 DIN 7627 FOR FUEL LINE CONNECTION	2
164		SEALING RING A 12 X 16 DIN 7603 FIBER FOR FUEL LINE CONNECTION	2
166	A 000 073 03 02→	VALVE CAP	2
167	A 000 071 35 71→	LENS-HD. COUNTERSUNK SCREW FOR VALVE CAP AT CARBURETOR COVER	6
168	A 000 070 07 52→	DIAPHRAGM STARTER MOTOR AIR VALVES	2
169	A 000 071 14 16→	VALVE SPRING	2
196	A 000 071 24 71→	SQUARE-HEAD SCREW	8
-----	A 000 990 05 47→	REPLACED BY 6 DIN 7980	0
197		LOCK WASHER 6 DIN 7980	8
201	A 188 141 01 62→	INSULATING FLANGE FOR CARBURETOR AT SUCTION TUBE	2
202	A 180 141 02 62→	INSULATING FLANGE FOR CARBURETOR AT SUCTION TUBE	2
203	A 180 141 00 23→	AIR NOZZLE FOR CARBURETOR AT SUCTION TUBE	2
204		SPRING WASHER A 8 DIN 137 FOR CARBURETOR AT SUCTION TUBE	8
205	A 000 990 08 51→	HEX. NUT FOR CARBURETOR AT SUCTION TUBE	8
206	A 121 070 00 55→	PROTECTING PLATE,	2
207	A 186 993 35 10→	RELEASE SPRING AT CARBURETOR	2
208	A 186 070 00 76→	PUSH ROD FOR CARBURETOR CONTROL	2
209	A 180 072 01 26→	CHOKE CABLE FOR CHOKE CONNECTION, FRONT AND REAR CARBURETOR	1
210	A 136 072 00 50→	BUSHING FOR CHOKE CONNECTION, FRONT AND REAR CARBURETOR	2
211		HEX. -HD. SCREW M 4X12 DIN 933-8 G FOR CHOKE CONNECTION, FRONT AND REAR CARBURETOR	2
212		SPRING WASHER B 4 DIN 137 FOR CHOKE CONNECTION, FRONT AND REAR CARBURETOR	2
213		HEX. NUT M 4 DIN 934-5 S FOR CHOKE CONNECTION, FRONT AND REAR CARBURETOR	2
214		WASHER 4, 3 DIN 125 FOR CHOKE CONNECTION, FRONT AND REAR CARBURETOR	2
220	A 180 070 07 32→	FUEL LINE, CARBURETOR	1
-----	A 180 995 03 01→	PIPE CLAMP FOR FUEL AND VACUUM LINE AT ENGINE Заменено на: A 186 995 01 01→	0
221	A 186 995 01 01→	PIPE CLAMP FOR FUEL AND VACUUM LINE AT ENGINE	1
-----		HEX.-HD. SCREW M 6X12 DIN 933-8 G FOR FUEL AND VACUUM LINE AT ENGINE UP TO ENGINE 7506624 FROM ENGINE 7506625 THE PIPE CLAMP IS FIXED W	1
-----		LOCK WASHER B6 DIN 127 FOR FUEL AND VACUUM LINE AT ENGINE UP TO ENGINE 7506624 FROM ENGINE 7506625 THE PIPE CLAMP IS FIXED WITH HEX.	1
-----		HEX. NUT M 6 DIN 934-5 S FOR FUEL AND VACUUM LINE AT ENGINE UP TO ENGINE 7506624 FROM ENGINE 7506625 THE PIPE CLAMP IS FIXED WITH	1

B07005A19001.051209
[image]