| № поз. |
Номер детали |
Название/дополнительная информация |
Колич |
Версия |
|
ENGINE
|
|
----- |
A 127 010 02 00→ |
REPLACED BY
127 010 07 00 TOGETHER WITH 1 DOWEL PIN 180 991 01 62 1 DOWEL PIN 180 991 02 62 FOR EXCHANGING AGAINST THE MOUNTED DOWEL |
0 |
LM |
|
----- |
A 127 010 06 00→ |
REPLACED BY
127 010 07 00 TOGETHER WITH 1 DOWEL PIN 180 991 01 62 1 DOWEL PIN 180 991 02 62 FOR EXCHANGING AGAINST THE MOUNTED DOWEL |
0 |
LM |
|
----- |
A 127 010 10 00→ |
ENGINE, COMPLETE,
WITHOUT STARTER MOTOR COMPRESSION 8.7
Заменено на: A 127 010 07 00→ |
0 |
LM |
|
----- |
A 127 010 07 00→ |
ENGINE, COMPLETE,
WITHOUT STARTER MOTOR COMPRESSION 8.7 FROM ENGINE 8500216 |
1 |
LM |
|
----- |
A 127 010 04 00→ |
REPLACED BY
127 010 09 00 TOGETHER WITH 1 DOWEL PIN 180 991 01 62 1 DOWEL PIN 180 991 02 62 FOR EXCHANGING AGAINST THE MOUNTED DOWL |
0 |
A |
|
----- |
A 127 010 09 00→ |
ENGINE, COMPLETE,
WITHOUT STARTER MOTOR COMPRESSION 8.7 FROM ENGINE 8500022 |
1 |
A |
|
CYLINDER CRANKCASE
|
|
----- |
A 127 010 12 08→ |
REPLACED BY
127 010 20 08 TOGETHER WITH 1 GUIDE TUBE 127 010 03 66 1 SEALING RING A 10X14 DIN 7603 AL 1 HEX.-HD.SCREW M 10X12 DIN 93 |
0 |
M |
|
----- |
A 127 010 12 08→ |
REPLACED BY
127 010 20 08 TOGETHER WITH 1 GUIDE TUBE 127 010 03 66 1 SEALING RING A 10X14 DIN 7603 AL 1 HEX.-HD.SCREW M 10X12 DIN 93 |
0 |
A |
|
----- |
A 127 010 13 08→ |
CYLINDER CRANKCASE
Заменено на: A 127 010 20 08→ |
0 |
|
|
1 |
A 127 010 20 08→ |
CYLINDER CRANKCASE
FROM ENGINE 8500216 |
0 |
M |
|
1 |
A 127 010 20 08→ |
CYLINDER CRANKCASE
FROM ENGINE 8500222 |
1 |
A |
|
----- |
B 40 N 59 a→ |
LOCKING PLATE
FOR LOCKING CORE HOLES, LATERAL |
3 |
|
|
----- |
B 40 N 59 a→ |
LOCKING PLATE
FOR LOCKING CORE HOLES, LATERAL UP TO ENGINE 000024 |
0 |
A |
|
----- |
|
LOCKING SCREW
M 30X1,5 DIN 906 FOR LOCKING CORE HOLES, LATERAL FROM ENGINE 000025 |
0 |
A |
|
----- |
|
SEALING RING
A 10 X 14 DIN 7603 AL FOR LOCKING THREADED BORE AT ENGINE SUSPENSION, LATERAL FROM ENGINE 000025 |
0 |
A |
|
----- |
|
HEX.-HD.SCREW
M 10 X 12 DIN 933-8 G FOR LOCKING THREADED BORE AT ENGINE SUSPENSION, LATERAL FROM ENGINE 000025 |
0 |
A |
|
2 |
A 180 011 00 11→ |
CRANKSHAFT BEARING CAP
FOR 1ST, 3RD AND 4TH CRANKSHAFT BEARING |
3 |
|
|
3 |
A 180 010 01 23→ |
CRANKSHAFT BEARING
CAP WITH TIGHTENING PIN FOR 2ND CRANKSHAFT BEARING |
1 |
|
|
4 |
A 121 991 00 41→ |
TIGHTENING PIN |
4 |
|
|
----- |
A 180 011 01 52→ |
GUARD PLATE
HALF 3-MM = STANDARD FOR CRANKSHAFT BEARING CAP
Заменено на: A 180 011 09 52→ |
0 |
|
|
5 |
A 180 011 09 52→ |
GUARD PLATE
HALF 3-MM = STANDARD FOR CRANKSHAFT BEARING CAP |
2 |
|
|
----- |
A 180 011 02 52→ |
GUARD PLATE
HALF, 3.05-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN
Заменено на: A 180 011 10 52→ |
0 |
|
|
----- |
A 180 011 10 52→ |
GUARD PLATE
HALF, 3.05-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
A 180 011 03 52→ |
GUARD PLATE
HALF, 3.10-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN
Заменено на: A 180 011 11 52→ |
0 |
|
|
----- |
A 180 011 11 52→ |
GUARD PLATE
HALF, 3.10-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
A 180 011 05 52→ |
GUARD PLATE
HALF, 3.15-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN
Заменено на: A 180 011 12 52→ |
0 |
|
|
----- |
A 180 011 12 52→ |
GUARD PLATE
HALF, 3.15-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
A 180 011 04 52→ |
GUARD PLATE
HALF, 3.20-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN
Заменено на: A 180 011 13 52→ |
0 |
|
|
----- |
A 180 011 13 52→ |
GUARD PLATE
HALF, 3.20-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
A 180 011 06 52→ |
GUARD PLATE
HALF, 3.25-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN
Заменено на: A 180 011 14 52→ |
0 |
|
|
----- |
A 180 011 14 52→ |
GUARD PLATE
HALF, 3.25-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
A 180 011 07 52→ |
GUARD PLATE
HALF, 3.30-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN
Заменено на: A 180 011 15 52→ |
0 |
|
|
----- |
A 180 011 15 52→ |
GUARD PLATE
HALF, 3.30-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
A 180 011 08 52→ |
GUARD PLATE
HALF, 3.35-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN
Заменено на: A 180 011 16 52→ |
0 |
|
|
----- |
A 180 011 16 52→ |
GUARD PLATE
HALF, 3.35-MM THICK FOR CRANKSHAFT BEARING CAP REPAIR DESIGN |
2 |
|
|
----- |
|
HEX.-HD.SCREW
M 12X75 DIN 931-10 K FOR CRANKSHAFT BEARING CAP AT CYLINDER CRANKCASE |
8 |
|
|
----- |
|
SPRING WASHER
B 12 DIN 137 FOR CRANKSHAFT BEARING CAP AT CYLINDER CRANKCASE |
6 |
|
|
----- |
|
CYLINDRICAL PIN
10 M6X16 DIN 7 FOR CRANKSHAFT BEARING CAP AT CYLINDER CRANKCASE |
4 |
|
|
----- |
|
CYLINDRICAL PIN
8 M6X16 DIN 7 FOR CRANKSHAFT BEARING CAP AT CYLINDER CRANKCASE |
4 |
|
|
6 |
A 180 186 02 40→ |
BRACKET FOR
INTAKE PIPE, OIL PUMP AT 2ND CRANKSHAFT BEARING IN CYLINDER CRANKCASE |
1 |
|
|
----- |
A 186 991 07 01→ |
CYLINDRICAL PIN,
DIA. 8 X 26-MM FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE UP TO ENGINE 8500215 |
1 |
M |
|
----- |
A 186 991 07 01→ |
CYLINDRICAL PIN,
DIA. 8 X 26-MM FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE UP TO ENGINE 8500021 |
0 |
A |
|
7 |
A 180 991 00 60→ |
DOWEL PIN,
DIA. 12 X 34-MM FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE FROM ENGINE 8500216 |
1 |
M |
|
7 |
A 180 991 00 60→ |
DOWEL PIN,
DIA. 12 X 34-MM FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE FROM ENGINE 8500022 |
0 |
A |
|
----- |
A 186 991 08 01→ |
CYLINDRICAL PIN,
DIA. 8 X 16-MM FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE UP TO ENGINE 8500215 |
1 |
M |
|
----- |
A 186 991 08 01→ |
CYLINDRICAL PIN,
DIA. 8 X 16-MM FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE UP TO ENGINE 8500021 |
0 |
A |
|
8 |
A 180 991 01 60→ |
DOWEL PIN,
DIA. 12 X 20-MM FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE FROM ENGINE 8500216 |
1 |
M |
|
8 |
A 180 991 01 60→ |
DOWEL PIN,
DIA. 12 X 20-MM FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE FROM ENGINE 8500022 |
0 |
A |
|
----- |
A 180 991 01 62→ |
DOWEL PIN
IN CASE OF CYL. CRANKCASE WITH DOWEL PIN DIA. 8-MM CLUTCH HOUSING WITH DOWEL PIN DIA. 12-MM AND INTERMEDIATE PLATE WITH |
1 |
|
|
----- |
A 180 991 02 62→ |
DOWEL PIN
IN CASE OF CYL. CRANKCASE WITH DOWEL PIN DIA. 12-MM CLUTCH HOUSING WITH DOWEL PIN DIA. 8-MM AND INTERMEDIATE PLATE WITH |
1 |
|
|
----- |
A 180 991 04 62→ |
DOWEL PIN
IN CASE OF CYL. CRANKCASE WITH DOWEL PIN DIA. 12-MM AND INTERMEDIATE PLATE WITH DOWEL PIN DIA. 8-MM RECESSED DIA. 12 MM |
1 |
|
|
----- |
A 180 991 03 62→ |
DOWEL PIN
IN CASE OF CYL. CRANKCASE WITH DOWEL PIN DIA. 12-MM INTERMEDIATE PLATE WITH DOWEL PIN DIA. 8-MM AND CLUTCH HOUSING WITH |
1 |
|
|
11 |
A 180 031 00 58→ |
SEALING RING HOLDER HALF
FOR OIL SEALING OF CRANKSHAFT |
1 |
|
|
----- |
|
LOCKING SCREW
M 16X1,5 DIN 906 FOR LOCKING OIL CHANNEL, FRONT AND REAR |
3 |
|
|
----- |
|
LOCKING SCREW
M 10X1 DIN 906 FOR LOCKING OIL BORE, LATERAL |
1 |
|
|
----- |
B 25 N 59 a→ |
LOCKING WASHER
FOR LOCKING CORE HOLE, OIL PUMP DRIVE NO LONGER INSTALLED |
0 |
|
|
----- |
|
DOWEL PIN
10X14 N 37 B FOR CYLINDER HEAD AT CYLINDER CRANKCASE |
2 |
|
|
----- |
|
STUD BOLT
M 8X18 DIN 939-8 G FOR SUPPORT, GENERATOR |
2 |
|
|
----- |
|
STUD BOLT
M 8X35 DIN 939-5 S FOR INJECTION PUMP AT CYLINDER CRANKCASE |
3 |
|
|
CYLINDER SIDE COVER
|
|
17 |
A 180 015 05 05→ |
CYLINDER SIDE COVER
AT STARTER MOTOR SIDE |
1 |
|
|
17 |
A 180 015 05 05→ |
CYLINDER SIDE COVER
AT STARTER MOTOR SIDE UP TO ENGINE 000024 |
0 |
A |
|
17a |
A 180 015 07 05→ |
CYLINDER SIDE COVER
AT STARTER MOTOR SIDE FROM ENGINE 000025 |
0 |
A |
|
20 |
A 180 015 05 21→ |
GASKET
FOR CYLINDER SIDE COVER AT CYL. CRANKCASE, STARTER MOTOR SIDE |
1 |
|
|
20 |
A 180 015 05 21→ |
GASKET
FOR CYLINDER SIDE COVER AT CYL. CRANKCASE, STARTER MOTOR SIDE UP TO ENGINE 000024 |
0 |
A |
|
20a |
A 180 015 08 21→ |
GASKET
FOR CYLINDER SIDE COVER AT CYL. CRANKCASE, STARTER MOTOR SIDE FROM ENGINE 000025 |
0 |
A |
|
----- |
|
HEX.-HD.SOCKET SCREW
M 6X15 DIN 912-8G FOR CYLINDER SIDE COVER AT CYL. CRANKCASE, STARTER MOTOR SIDE |
28 |
|
|
----- |
|
HEX.-HD.SOCKET SCREW
M 6X15 DIN 912-8G FOR CYLINDER SIDE COVER AT CYL. CRANKCASE, STARTER MOTOR SIDE UP TO ENGINE 000024 |
0 |
A |
|
----- |
|
HEX.-HD.SOCKET SCREW
M 6X15 DIN 912-8G FOR CYLINDER SIDE COVER AT CYL. CRANKCASE, STARTER MOTOR SIDE FROM ENGINE 000025 |
0 |
A |
|
----- |
A 180 990 10 40→ |
WASHER
FOR CYLINDER SIDE COVER AT CYL. CRANKCASE, STARTER MOTOR SIDE |
28 |
|
|
----- |
A 180 990 10 40→ |
WASHER
FOR CYLINDER SIDE COVER AT CYL. CRANKCASE, STARTER MOTOR SIDE UP TO ENGINE 000024 |
0 |
A |
|
----- |
|
WASHER
6,4 DIN 125 FOR CYLINDER SIDE COVER AT CYL. CRANKCASE, STARTER MOTOR SIDE FROM ENGINE 000025 |
0 |
A |
|
----- |
|
HEX.-HD.SCREW
M 6X12 DIN 933-8 G FOR CYLINDER SIDE COVER AT CYL. CRANKCASE, STARTER MOTOR SIDE |
1 |
|
|
----- |
|
SPRING WASHER
A 6 DIN 137 FOR CYLINDER SIDE COVER AT CYL. CRANKCASE, STARTER MOTOR SIDE |
1 |
|
|
26 |
|
DISCHARGE VALVE
CM 14X1,5 KEG DIN 71401 |
1 |
|
|
----- |
A 621 052 01 50→ |
BEARING BUSHING
FOR INTERMEDIATE GEAR SHAFT, REAR SEE GROUP 05 |
1 |
|
|
----- |
A 180 011 06 05→ |
INTERMEDIATE PLATE,
HOLE DIA.8-MM FOR CYLINDER CRANKCASE STARTER MOTOR UP TO ENGINE 8500215 |
1 |
M |
|
----- |
A 180 011 06 05→ |
INTERMEDIATE PLATE,
HOLE DIA.8-MM FOR CYLINDER CRANKCASE STARTER MOTOR UP TO ENGINE 8500021 |
0 |
A |
|
----- |
A 180 011 13 05→ |
INTERMEDIATE PLATE,
HOLE DIA. 12-MM FOR CYLINDER CRANKCASE STARTER MOTOR
Заменено на: A 180 011 11 05→ |
0 |
|
|
28 |
A 180 011 11 05→ |
INTERMEDIATE PLATE,
HOLE DIA. 12-MM FOR CYLINDER CRANKCASE STARTER MOTOR FROM ENGINE 8500216 |
1 |
M |
|
28 |
A 180 011 11 05→ |
INTERMEDIATE PLATE,
HOLE DIA. 12-MM FOR CYLINDER CRANKCASE STARTER MOTOR FROM ENGINE 8500022 |
0 |
A |
|
----- |
|
HEX.-HD.SCREW
M 10 X 15 DIN 933-8 G FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE UP TO ENGINE 8500215 |
2 |
M |
|
----- |
|
HEX.-HD.SCREW
M 10 X 15 DIN 933-8 G FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE UP TO ENGINE 8500021 |
0 |
A |
|
----- |
|
HEX.-HD.SCREW
M 10 X 15 DIN 933-8 G FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE FROM ENGINE 8500216 |
3 |
M |
|
----- |
|
HEX.-HD.SCREW
M 10 X 15 DIN 933-8 G FOR INTERMEDIATE PLATE AT CYLINDER CRANKCASE FROM ENGINE 8500022 |
0 |
A |
|
OIL PAN
|
|
30 |
A 180 010 31 13→ |
OIL PAN WITH LOCKING PIN |
1 |
|
|
31 |
A 180 031 00 58→ |
SEALING RING HOLDER HALF |
1 |
|
|
31 |
A 180 031 00 58→ |
SEALING RING HOLDER HALF
UP TO ENGINE 000035 |
0 |
A |
|
31a |
A 186 991 00 55→ |
LOCKING PIN
FROM ENGINE 000036 |
0 |
A |
|
33 |
A 621 018 01 28→ |
ELBOW FITTING
FOR GUIDE TUBE OIL DIPSTICK AT CYLINDER CRANKCASE |
1 |
|
|
34 |
A 621 997 01 40→ |
SEALING RING
FOR GUIDE TUBE OIL DIPSTICK AT CYLINDER CRANKCASE |
2 |
|
|
----- |
|
HEX.-HD.SOCKET SCREW
M 8 X 12 DIN 912-8 G FOR GUIDE TUBE OIL DIPSTICK AT CYLINDER CRANKCASE |
1 |
|
|
35 |
A 127 010 02 66→ |
GUIDE TUBE
IN THE OIL PAN FOR OIL DIPSTICK |
1 |
|
|
----- |
A 180 997 00 40→ |
SEALING RING
FOR OIL DIPSTICK
Заменено на: A 198 997 00 40→ |
0 |
|
|
36 |
A 198 997 00 40→ |
SEALING RING
FOR OIL DIPSTICK |
1 |
|
|
37 |
A 127 010 01 72→ |
OIL DIPSTICK
WITH BREATHER FILTER |
1 |
|
|
----- |
|
SEALING RING
C 26 X 32 DIN 7603 CU-ASB FOR OIL DRAIN, OIL PAN |
1 |
|
|
40 |
A 136 997 12 30→ |
LOCKING SCREW M 26X1,5
FOR OIL DRAIN, OIL PAN |
1 |
|
|
----- |
|
WASHER
6,4 DIN 433 FOR OIL PAN AT CYLINDER CRANKCASE |
22 |
|
|
----- |
|
HEX.-HD.SOCKET SCREW
M 6 X 15 DIN 912-8 G FOR OIL PAN AT CYLINDER CRANKCASE |
20 |
|
|
----- |
|
HEX.-HD.SOCKET SCREW
M 6 X 40 DIN 912-8 G FOR OIL PAN AT CYLINDER CRANKCASE |
2 |
|
|
----- |
|
HEX.-HD.SOCKET SCREW
M 8 X 35 DIN 912-8 G FOR OIL PAN AND ENGINE MOUNTING AT CYLINDER CRANKCASE |
2 |
|
|
----- |
|
WASHER
8,4 DIN 433 FOR OIL PAN AT CYLINDER CRANKCASE |
0 |
|
|
----- |
|
HEX.-HD.SOCKET SCREW
M 8 X 80 DIN 912-8 G FOR OIL PAN AT CYLINDER CRANKCASE |
2 |
|
![[image]](https://img.nemcy-zdes.ru/mb/BM_IMAGES_ARC/B01001A17001.051209.png)
